37mm Metal Gear Step Motor – 41mm Type Model NFP-GM37BY-M6-L
DC Brushless Step Gear Reduction Motor Parameters
Stepper control: Convert electrical pulse signals into angular displacement control for easy intelligent control.
High gear precision: wear-resistant, strong torque resistance, long life, fast heat dissipation, strong composite ability.
D-shaped output shaft: more convenient to install, not easy to slip, save installation time.
Two-phase four-wire: brushless stepper motor, low noise positioning.
Full metal gear: using full metal gear material, making it more wear-resistant and extending service life.
Features: The lower the reduction ratio, the larger the step angle and the smaller the torque; The larger the reduction ratio, the smaller the step angle and the greater the torque.
Phase current: 100mA at 5V; 600mA at 12V.
Speed regulation frequency range: 300-1000PPS (it is recommended to start from 300PPS and stabilize the speed at about 700PPS).
| Motor Model | NFP-GM37BY-M6-L |
|---|---|
| Motor Diameter | 35mm |
| Shaft Length & Diameter | L-58mm & ∅-M6mm |
| Rated Voltage | 12V DC |
| Available Voltage Range | 3.7V − 24V |
| Phase Resistance | 30Ω/phase ± 15% |
| Step Angle | 7.5°/Step |
| Phase Number | 2 phases |
| Drive Mode | Bipolar Drive |
| Pull-out Torque | ≥300g.cm at 100PPS |
| Holding Torque | ≥600g.cm at 0PPS |
| Current Per Phase | 0.4A/phase |
| Max Response Frequency | 750PPS/Hz |
| Max Starting Frequency | 700PPS/Hz |
| Insulation Class | Class E for coils |
| Insulation Resistance | 100MΩ DC 500V |
| Insulation Strength | 100V AC for one second |
| Operating Temperature | -10°C ~ +55°C |
| Wiring | yellow A, Green A-, Red B-, Black B |
| Weight | 165g − 200g |
NFP-GM37BY-M6-L, Operating Voltage: 12V DC, Test Frequency: 400PPS/Hz, 500RPM
| Ratio | Step | No Load Speed | Holding Torque | Pull-out Torque |
|---|---|---|---|---|
| 6.3 :1 | 1.19° | 79 rpm | 2.8 kgf.cm | 1.2 kgf.cm |
| 10 :1 | 0.75° | 50 rpm | 4.5 kgf.cm | 2 kgf.cm |
| 18.8 :1 | 0.399° | 26 rpm | 8 kgf.cm | 3.5 kgf.cm |
| 30 :1 | 0.25° | 16 rpm | 13 kgf.cm | 6 kgf.cm |
| 50 :1 | 0.15° | 10 rpm | 22 kgf.cm | 10 kgf.cm |
| 67 :1 | 0.112° | 7 rpm | 30 kgf.cm | 13 kgf.cm |
| 90 :1 | 0.083° | 5.5 rpm | ≤30 kgf.cm | 18 kgf.cm |
| 150 :1 | 0.05° | 3.3 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
| 270 :1 | 0.027° | 1.9 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
| 450 :1 | 0.0167° | 1.1 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
| 630 :1 | 0.012° | 0.8 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
| 810 :1 | 0.0093° | 0.6 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
NFP-GM37BY-M6-L, Operating Voltage: 24V DC, Test Frequency: 600PPS/Hz, 750RPM
| Ratio | Step | No Load Speed | Holding Torque | Pull-out Torque |
|---|---|---|---|---|
| 6.3 :1 | 1.19° | 119 rpm | 3.5 kgf.cm | 2 kgf.cm |
| 10 :1 | 0.75° | 75 rpm | 5.5 kgf.cm | 3.2 kgf.cm |
| 18.8 :1 | 0.399° | 40 rpm | 10 kgf.cm | 5.8 kgf.cm |
| 30 :1 | 0.25° | 25 rpm | 16.5 kgf.cm | 9 kgf.cm |
| 50 :1 | 0.15° | 15 rpm | 25 kgf.cm | 15 kgf.cm |
| 67 :1 | 0.112° | 11 rpm | ≤30 kgf.cm | 20 kgf.cm |
| 90 :1 | 0.083° | 8.3 rpm | ≤30 kgf.cm | 28 kgf.cm |
| 150 :1 | 0.05° | 5 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
| 270 :1 | 0.027° | 2.7 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
| 450 :1 | 0.0167° | 1.7 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
| 630 :1 | 0.012° | 1.2 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
| 810 :1 | 0.0093° | 0.9 rpm | ≤30 kgf.cm | ≤30 kgf.cm |
Warning: The maximum instantaneous load of the reducer should not exceed 6.0kg.cm, otherwise the reducer will be damaged and the whole motor will be damaged!
BLDC Metal Gearbox Stepper Motor Outline Drawing

Optional mounting bracket & flange coupling (Just make a note when placing an order)


Brushless DC Stepping Gear Motor Connection Diagram
Terminal wiring sequence description: 1.25-4Y Wiring terminal, Wire: GB1571 30/UL, AWM, 105°

Keywords:
step gear motor, stepper dc gear motor, stepping geared motor
Additional information
| Option | 12V DC, Ratio 1: 10, 24V DC, Ratio 1: 10 |
|---|
Free Shipping Site-wide When You Spend More Than $150
Click The Following Button To Copy the Coupon Code When You’re Going To The Checkout
Still can't find ideal motors?
Get A Quote Within 8 Hours Contact Now! Any question about Micro DC Motor, Spec, Data-Sheet, Quote...
If you want a custom lead wire connection of the water resistant vibration motors. Such as alternate lead wire length & strip lengths, with a connector (e.g. Molex, JST). You can contact us from the footer form, tell us your need. Any problems will be taken seriously and will be answered professionally, so pls do not hesitate to contact us by the footer form.






Reviews
There are no reviews yet.